Seeing was kinda in and out last night, here's the best view I had of Jupiter and it's fading GRS!

 

1st Post in some time of Jupiter with Europa in transit with shadow!

 Lots of clear nights this stretch but none super great seeing, above avg at best with lots of smoke and haze from wild fires! :(

Perseids Meteor shower 2021

 I only spent a total of like 5minutes outside with my unaided eye on Wed, Aug 11, 2021.  My allsky setup -http://astromaphilli14.blogspot.com/2019/03/my-diy-astropi-allsky-system.html - was able to grab a pair of really bright meteors!

The latter of the two left a decent after glow as seen in the animation.

 

 

Building a dual temperature sensor on a RaspberryPi for a custom telescope cooling system

 

For that that don't follow me on social media or know what a true inner nerd you are dealing with. 

 

The key to using the cooling system is knowing what the mirror and air temps are. 

One you know what the temperature difference is you have to know when to cycle the cooling on and off

and that is a bit of black magic.  After the indoor/outdoor thermometer I previously used died I decided to build

a dual digital  temp sensor monitor on a rasberryPi to compare the mirror and air temps.

 

Sensors

I purchased 2x AM2320's as they were relatively inexpensive, with good accuracy and built in resistors!

I followed this schematic to get them tested

 

I somewhat assumed that you could have them in a series and assign them roles or addresses.  I was wrong!

 

Finding the best method to READ values from the sensor wasn't too hard in python but using the right timing got

tricky.  I ended up using this runtime compile library - https://github.com/rhubarbdog/am2320 

 This allowed me to use python's popen and appeared most stable for me.

 

 

Challenges

I bought 2x AM2320 and THEN discovered that you cannot use them together without some additional efforts.

Not a big deal but the Internet is full of pitfalls.  Here's the solution I came up with from some help of a fellow

redditor - /u/I_Generally_Lurk -

https://www.reddit.com/r/raspberry_pi/comments/mbw08x/multiple_am2320_temp_sensors_on_a_pi4/

 

 

His suggestion of using a multiplexer got me on the right path to this solution:

 

I2C multiplexer

I found this tidbit that detailed how to use a different GPIO bus, created in software to allow each sensor to

operate independently - https://www.instructables.com/Raspberry-PI-Multiple-I2c-Devices/

 

The beauty of this solution is that the sensor read code from rhubarbdog had the bus specified in the source.

A quick edit and I had two copies of his pre-compiled code, one on bus1 and a second on bus4.  I ran into a

 performance issue that was again fixed in software!  PHEW!  After a good deal of fiddling, I found a slowness 

issue on the 2nd bus which was resolved using the following.

 

FIX for slow

https://github.com/raspberrypi/linux/issues/1467

 

Another link that could help -

https://github.com/raspberrypi/firmware/issues/1401

 

 

Wiring

 

 

Now that I am able to address each sensor individually using the following setup

 

Sensor ONE on BUS1

Sensor TWO on BUS4

 

This script:

 

def temp():

        global mirrorT

        global airT

        global mirrorH

        global airH

        global D

        try:

                sp = subprocess.Popen('/home/pi/am2320/run.sh',

                        shell=True,

                        stdout=subprocess.PIPE,

                        stderr=subprocess.PIPE,

                        universal_newlines=True)

                air,err=sp.communicate()

                # Store the return code in rc variable

                rc=sp.wait()

# string sort of output for desired values

                airT=float(air[:-26][12:])

                airH=float(air[:-5][33:])

        except:

                # pre-store values to prevent scrtipt from stopping if sensors have errorsairT=1.1

                airH=1.1

                pass

        try:

                sp = subprocess.Popen('/home/pi/am2320.Bus4/run.sh',

                        shell=True,

                        stdout=subprocess.PIPE,

                        stderr=subprocess.PIPE,

                        universal_newlines=True)

                mirror,err=sp.communicate()

                # Store the return code in rc variable

                rc=sp.wait()

                # string sort of output for desired values

mirrorT=float(mirror[:-26][12:])

                mirrorH=float(mirror[:-5][33:])

        except:

                # pre-store values to prevent scrtipt from stopping if sensors have errors

mirrorT=1.1

                mirrorH=1.1

                pass

        D=mirrorT-airT

        return mirrorT,airT,mirrorH,airH,D

 

 

 allows me to read both at the same time and display's this output!

 

 

Air Temperature:  66.38

Air Humidity:  50.5

 

Mirror Temperature:  66.2

Mirror Humidity:  50.6

 

 

 

At this point I was able to do fun things like put a mug of ice water near one of the sensors to determine that

they were both reading independently.  Then I needed to wire up one of them longer than the other in order to

stretch to the mirror.  I used an old, spare, CAT5 Ethernet cable and simply inserted a stripped end into the female

end of a jumper breadbox cable!

 

Here's the final design as it is attached to the scope.  Note one sensor is reading the air and hanging loose, the

other routes up the cat5 cable to the mirror.

 

 

 

 

The green cable routes up the mount to the mirror where the sensor is on the other end, taped in place.  As

you can see in the close up below, I didn't solder the cables to the jumpers, only secure with tape which has held

good enough for now!

 

 

 

The values are only read via script for the time being but watch for the next installment where we will learn how

I wrote them to an Influx database for use within Grafana and Home Assistant!